The PnP TW coil is not a replacement for every Voopoo coil. It is a specific sub-series with a specific liquid requirement, and if you put the wrong e-liquid through it, it will burn within a tank regardless of what device you own. This guide explains exactly what the TW series is, which devices accept it, what wattage to run, and why the liquid ratio matters more here than with any other coil in the PnP family.
The Voopoo PnP TW coil series includes the TW15 (0.15Ω, 55-70W) and TW20 (0.2Ω, 40-55W), both mesh-build, push-fit coils designed for DTL vaping with 50/50 VG/PG freebase or nicotine salt e-liquids. They are compatible with legacy PnP platform devices including the Drag S, Drag X, Drag H80S, Drag E60, Drag 3, Drag 4, Argus Pro, Argus GT, Vinci series, and PnP Pod II. They are NOT compatible with PnP X platform devices (Drag X2, S2, X3, S3, Drag 5, Drag 6, Argus Pro 2). KandyVape stocks the TW coils as a 5-pack at current price listed on the product page.
What the TW Series Actually Is
Voopoo’s PnP coil range has three distinct generations. The original VM series, which launched with the Vinci pod kit, uses a mesh build and works across a wide VG/PG range. The TW series, which Voopoo introduced later, uses what Voopoo describes as “Dual-in-One technology”: a structural change to the coil’s heating element that Voopoo rates as producing faster heat-up and richer vapor than the equivalent-resistance VM coil. The third generation is the PnP X, a physically different platform for newer devices only.
TW stands for Turbo Watt. The name reflects the coil’s orientation toward higher-wattage DTL use. The TW15 at 0.15Ω runs between 55W and 70W. The TW20 at 0.2Ω runs between 40W and 55W. These wattage ranges are confirmed against Voopoo’s own product specification data on the official PnP coil page at shop.voopoo.com.
There is also a TW30 (0.3Ω, 28-36W, RDTL) that exists in the wider PnP ecosystem. KandyVape does not currently stock this variant. If you need the TW30, check the product page for current availability. The specs in this guide cover the TW15 and TW20, which are the stocked variants.
The Wicking Constraint You Must Understand Before Ordering
This is the specification most online guides bury or omit entirely. The TW series uses smaller wicking ports than the VM series. That design choice is intentional: smaller ports support the Dual-in-One heating structure and work correctly with thinner e-liquids. The practical consequence is direct.
If you run a 70% VG or higher e-liquid through a TW coil, the liquid will not wick to the heating surface fast enough.
The cotton will dry out between draws, and the coil will burn. The first burn is usually subtle, a slight change in flavor. Within a few more draws, it is irreversible. The coil is done.
The TW series requires 50/50 VG/PG e-liquid, or nicotine salt formulations, which are typically 50/50 by default. Propylene glycol (PG) is the thinner of the two base liquids. The PubChem entry for propylene glycol (CID 1030) records it as a low-viscosity compound with established food-grade safety classifications, which is why it carries liquid through wicking cotton more readily than the thicker vegetable glycerin (VG). Glycerol (VG, PubChem CID 753) is significantly more viscous, which is why a 70/30 or 80/20 VG/PG liquid that works well in a VM6 will stall in a TW15.
If your current liquid is 70% VG or above, the TW coil is not the right choice for your setup. The VM5 (0.2Ω) or VM6 (0.15Ω) will accept higher-VG liquids and are the correct equivalents for that liquid type. No return is possible once a coil has been used, so making this decision correctly before you order is the only option.
Compatibility: Which Devices Accept PnP TW Coils
The PnP TW coils use the same push-fit connector as the entire legacy PnP platform. That means physical fit is consistent across all legacy PnP devices. However, physical fit alone does not confirm compatibility. Your device must also support the wattage range the coil requires.
The TW15 at 0.15Ω needs 55W to 70W. If your device’s maximum output sits below 55W, it will run the coil undercooked: low vapor, poor flavor, and a coil that floods rather than vaporizes. The TW20 at 0.2Ω needs 40W to 55W, which most mid-range PnP devices can reach comfortably.
| Device | TW15 (0.15Ω, 55-70W) | TW20 (0.2Ω, 40-55W) | Notes |
| Drag S | Compatible | Compatible | Confirm max output covers 55W for TW15 |
| Drag X | Compatible | Compatible | Standard legacy PnP device |
| Drag H80S | Compatible | Compatible | TW15 was introduced with this device |
| Drag E60 | Compatible | Compatible | TW20 was introduced with this device |
| Drag 3 | Compatible | Compatible | Legacy PnP platform |
| Drag 4 | Compatible | Compatible | Legacy PnP platform |
| Argus Pro | Compatible | Compatible | Verify device wattage ceiling before ordering TW15 |
| Argus GT | Compatible | Compatible | Standard legacy PnP device |
| Vinci / Vinci R / Vinci X / Vinci 2 / Vinci Air | Compatible | Compatible | Confirm individual device wattage ceiling |
| PnP Pod II | Compatible | Compatible | Voopoo’s dedicated PnP pod tank |
| Drag X2 / S2 | NOT compatible | NOT compatible | PnP X platform only |
| Drag X3 / S3 | NOT compatible | NOT compatible | PnP X platform only |
| Drag 5 / Drag 6 | NOT compatible | NOT compatible | PnP X platform only |
| Argus Pro 2 | NOT compatible | NOT compatible | PnP X platform only |
The PnP X platform devices use a physically different coil. TW and VM coils will not fit correctly in a PnP X pod. If you own one of the newer X-series devices, you need PnP X coils, not the TW series. Buying TW coils for a PnP X device is one of the most frequent purchasing errors in this category. Check your device model against this table before ordering.
Device compatibility data is verified against Voopoo’s official PnP platform and coil specification pages.
Resistance, Wattage, and Nicotine Pairing
The resistance you choose determines the draw style, the vapor volume, and the nicotine concentration that will be comfortable to use. At 0.15Ω (TW15), the vapor output is high and the draw is fully open DTL. At that production level, high-strength nicotine becomes uncomfortable within a few draws. Voopoo’s own guidance recommends a maximum of 10mg nicotine for the TW15.
At 0.2Ω (TW20), the vapor output is slightly lower and the airflow can be tightened to a restricted DTL draw. This is slightly more forgiving with nicotine concentration, though it still sits in the DTL range. Nicotine salt at 20mg and above is not the intended pairing for either TW variant at typical vaping frequency. Those concentrations are designed for MTL coils at 0.6Ω to 1.2Ω, where vapor production per draw is much lower.
| Coil | Resistance | Wattage | Draw Style | Recommended Liquid | Max Nicotine (Voopoo guidance) |
| PnP-TW15 | 0.15Ω | 55-70W | DTL | 50/50 VG/PG or nicotine salt | 10mg |
| PnP-TW20 | 0.2Ω | 40-55W | DTL / tight DTL | 50/50 VG/PG or nicotine salt | Check on device and liquid |
Running 20mg or 50mg nicotine salt through either of these coils at full wattage is a pairing that most people will find too harsh to maintain.
We would rather say that clearly here than have you make the purchase and discover it on the first tank with no recourse.
TW vs VM: When Each Series Makes Sense
The TW15 and VM6 are both 0.15Ω. The TW20 and VM5 are both 0.2Ω. They are not interchangeable. The VM series suits higher-VG liquids and a wider range of nicotine concentrations. The TW series suits 50/50 liquids and lower nicotine strengths, and Voopoo rates it as producing faster heat-up and denser vapor for its power input.
If you are currently using a high-VG freebase e-liquid, use the VM coil in the same resistance. If you are using nicotine salt in a 50/50 base and want open DTL with strong vapor, the TW coil is the correct choice. The decision comes down to your liquid, not your device.
How to Prime and Install a PnP TW Coil
Push-fit installation takes a few seconds. Remove the pod base or tank, pull the used coil straight out, push the new TW coil firmly into the seat until it clicks or seats flush, then refill with your 50/50 liquid before the coil goes into the device. Let it sit for at least five minutes before taking the first draw. Ten minutes is better. The cotton needs to be fully saturated before any heat is applied. Starting dry, even briefly, will damage the cotton and produce a burnt taste that cannot be reversed.
Start at the lower end of the wattage range. For the TW15, begin around 55W to 58W and move upward only if the vapor and flavor are not where you want them. For the TW20, start around 40W to 43W. Coils that are run too hard before the cotton has fully broken in tend to have shorter usable lifespans, though lifespan varies significantly depending on liquid sweetener content, vaping frequency, and whether the tank is consistently kept topped up. A coil run regularly on a high-sweetener liquid at maximum wattage will need replacing far sooner than one run on a simple salt nicotine base at moderate power.
Verifying Authenticity Before You Use the Coil
Counterfeit Voopoo coils exist in Bangladesh’s market. A fake coil is not simply a worse experience. It is a component with untested metal alloys, inconsistent mesh density, and no calibrated wicking, installed in a device that assumes the coil behaves within known parameters. Voopoo’s guide on genuine versus counterfeit coil performance documents the structural differences between authentic and inferior coils, including resistance drift, mesh irregularities, and the effect on device chipset behavior over time.
When your order arrives, inspect the packaging before you open it. Authentic Voopoo coil packaging carries a scratch-off security label on the box. Scratch the silver coating slowly. There are two verification methods: scan the QR code beneath the silver coating using a phone camera, or enter the alphanumeric code at voopoo.com/securitycode.html. If the code has already been used or does not register as genuine, the coil is not authentic. Do not use it.
Physical inspection on the coil itself: the metal sheath should be consistent in finish with no visible tool marks or discoloration.
The cotton visible through the wicking ports should be white, not off-yellow or compressed unevenly. On first fire, resistance displayed on the device screen should match the labeled value within 0.02Ω. Drift above that within the first tank is worth noting; consistent drift throughout the tank suggests a coil quality issue.
KandyVape stocks Voopoo products through an authorised supply chain. If you purchase from social media group orders, informal resellers, or marketplace listings at prices substantially below our product page price, the verification step above is not optional.
Ordering and Logistics
KandyVape dispatches orders daily at 3:00 PM, including weekends, from our physical store at Shop 22, Level 3, Sahabuddin Plaza, Adabar, Mohammadpur, Dhaka. Orders placed before 3:00 PM on a given day are included in that day’s dispatch. Orders above 3,500 BDT qualify for free shipping. Delivery charges below that threshold vary by location: check current rates on the product page or contact us before ordering.
KandyVape operates a strict [No-Return and No-Refund policy] on all products. This guide exists because a wrong coil choice has no correction path once the order is placed. Read the compatibility table against your device model, confirm your liquid VG/PG ratio, and verify the wattage range your device can deliver before ordering. Those are the three decisions that determine whether this coil works for you.
FAQ
Q: Will PnP TW coils fit my Voopoo Drag X2 or Drag S2?
No. The Drag X2, Drag S2, Drag X3, Drag S3, Drag 5, Drag 6, and Argus Pro 2 use the PnP X platform. PnP X pods accept PnP X coils only. The TW and VM series are physically incompatible with PnP X devices. If you own one of these devices, you need PnP X coils, not the TW series. Check your device model carefully before ordering.
Q: Can I use high-strength nicotine salt, such as 35mg or 50mg, with the TW15 or TW20?
This is not the intended pairing for either coil. Both the TW15 and TW20 are DTL coils that produce substantial vapor per draw. At that output level, 35mg or 50mg nicotine salt will produce a throat hit that most users find difficult to sustain. Voopoo’s own guidance for the TW15 recommends a maximum of 10mg nicotine. If you are using high-strength salt nicotine, MTL coils in the 0.6Ω to 1.2Ω range are the correct technical pairing.
Q: What is the difference between PnP TW15 and PnP VM6? They are both 0.15Ω.
Both coils share the same resistance but they are not interchangeable equivalents. The VM6 runs at 60W to 80W and suits higher-VG liquids. The TW15 runs at 55W to 70W and is optimized for 50/50 e-liquids, with smaller wicking ports that will not feed high-VG liquid fast enough. If your liquid is 70% VG or above, the VM6 is the correct choice. If your liquid is 50/50 freebase or nicotine salt, the TW15 is the appropriate coil.
Q: When will my order arrive after I place it?
KandyVape dispatches every day at 3:00 PM, including weekends. If your order is placed and confirmed before 3:00 PM, it leaves the same day. Delivery windows vary by location. If you are based inside Dhaka, check current delivery estimates on the product page or contact us directly. For outside Dhaka, delivery takes longer. We do not guarantee delivery windows beyond the dispatch commitment.
Q: How long do PnP TW coils last?
Coil lifespan depends on a combination of variables: liquid sweetener content, daily vaping frequency, whether you consistently stay within the rated wattage, and how reliably you keep the tank topped up. A heavily sweetened liquid run at maximum wattage with the tank frequently running low will exhaust a coil significantly faster than a simple nicotine salt base used at moderate wattage with consistent refilling. Voopoo does not publish a specific lifespan figure for TW coils. We will not invent one. When flavor begins to degrade noticeably or you detect a burnt character that does not clear after a few draws, the coil needs replacing.
Q: What happens if I buy the wrong coil and it does not work for my setup?
KandyVape’s No-Return and No-Refund policy applies to all products without exception. There is no exchange process for a coil purchased in error. This guide is written at the level of detail it is because that policy is real and immovable. If you are uncertain whether the TW coil is correct for your device or your liquid, contact us before ordering. We would rather answer a compatibility question before a purchase than have you hold a product you cannot use.
Q: How do I check if my Voopoo TW coils are genuine?
Locate the scratch-off security label on the coil packaging. Scratch the silver coating and either scan the QR code with your phone or enter the alphanumeric code at voopoo.com/securitycode.html. If the code is confirmed as genuine and first use, the coil is authentic. If the code has already been used or does not register, contact Voopoo directly before using the coil. Physical signs of a counterfeit include off-color packaging, cotton that appears compressed or off-white at the wicking ports, and resistance readings that drift more than 0.02Ω from the labeled value within the first tank.
Closing Note
If your device is in the legacy PnP family, your liquid is 50/50 VG/PG or a nicotine salt formulation, and your nicotine strength is at or below 10mg for DTL use, the TW15 or TW20 is a technically appropriate coil for your setup. If any of those three conditions do not apply, work through this guide again to identify the correct coil before ordering. You can also visit us in person at Shop 22, Level 3, Sahabuddin Plaza, Adabar, Mohammadpur, Dhaka, where the coils are available to inspect before purchase.
